stanley in My Home& Garden

Can i program a craftsman garage door remote to a Stanley garage door opener? If so how do i program it? I cant program the remote with stanley instructions. ... (Asked by Chad S)
View Entire Question \| Report Abuse \| Similar Questions \| See it in Y!
A.
No it will not work. for one the frequencies are prolly different and for two the number of dip switches is prolly different. Stanley garage door openers went bankrupt but parts are still available...(Answered by DOOR MAN)

View Entire Answer \| Report Abuse \| See it in Y!

a stanley range cooker engineer? to repair a stanley in sussex ... (Asked by f)
View Entire Question \| Report Abuse \| Similar Questions \| See it in Y!
A.
Check Stanley's web site. Their user manual should help....(Answered by Ed)

View Entire Answer \| Report Abuse \| See it in Y!

I require a FULL installation and service manual for a gas fired Stanley Aga range (heating & cooking).? The Stanley Range is 3 years old and the service manual is lost. ... (Asked by gownafish)
View Entire Question \| Report Abuse \| Similar Questions \| See it in Y!
A.
I would go to Stanley Aga on the Internet and click on CONTACT in the left hand column. Then ask them for a user manual. You probably can download it....(Answered by Ed)

View Entire Answer \| Report Abuse \| See it in Y!

Why won't my Stanley screw driven garage door opener go up? I have a Stanley screw driven garage door opener and it won't open. It will go down just fine, but when I try to open it, it will only open a few inches. I tried adjusting the open force a little bit, but that didn't help. Can anybody help me? ... (Asked by Rebel)
View Entire Question \| Report Abuse \| Similar Questions \| See it in Y!
A.
Hi ,My friend I assume you have power to the device. It may be that your travel limits are some how off.The set screws holding them in place may have loosened up.Take a look at the limits.Every thing else seems to be alright.That`s my tip for today,Good Luck ROSCO...(Answered by rosco)

View Entire Answer \| Report Abuse \| See it in Y!

how do i find stud center on house with vinyl siding? i have the stanley tool and it works fine inside .? I HAVE THE STANLEY STUD FINDER AND IT WORKS FINE INSIDE BUT I NEED TO FIND THE STUDS FROM OUTSIDE. I AM TRYING TO HANG AN AWNING AND MUST FINE STUD CENTER ... (Asked by joe h)
View Entire Question \| Report Abuse \| Similar Questions \| See it in Y!
A.
It seems to me that you could find it on the inside and then measure from a stable marker, such as a door or window, and translate that measurement to the outside. On the other hand, I know nothing of construction or stud finders. A thermal imaging device might work but I don't think that is in most tool boxes....(Answered by laughter_every_day)

View Entire Answer \| Report Abuse \| See it in Y!

I have a 12' Stanley Leverlock tape measure that has small black diamonds @ 19 & 3/16, 38 & 3/8ths and so on. All tapes have these same markings. I've asked people in the trades and have struck out. Does anybody out there know what these markings indicate? ... (Asked by TERRY K)
View Entire Question \| Report Abuse \| Similar Questions \| See it in Y!
A.
The so-called diamond mark is actually positioned at exactly 8/5 of a foot (that's exactly 1.6' or 19.2 inches, which is indeed pretty close to 19" 3/16 ). The diamond marks are also called "black truss" markings, because they correspond to the truss layout which is used with 8-foot sheets of plywood (or other material), namely 5 trusses per sheet. This is to be contrasted with "red stud" markings which appear every 16 inches by showing the corresponding inch number in red instead of black. The black markings and the red markings coincide at 8-foot intervals (96 inches). That is to say: 5 ...(Answered by shaula359)

View Entire Answer \| Report Abuse \| See it in Y!

How to replace the blade in Stanley utility knife? I need to replace the blade in Stanley utility knife. The replacement blade is trapazoidal in shape, and has two small open slots on the short edge. I am trying to insert the balde through the open slit in the front of the knife, but the blade does not get secured enough to slide it in and out of the knife. ... (Asked by ravishanti)
View Entire Question \| Report Abuse \| Similar Questions \| See it in Y!
A.
if you have one of those quick change knives,, you need to make shure the button us pushed all way forward, just past the 4th knotch and then hit the side button to alow removal of old blade, but hold thumb button forward while pushing in new blade, or will slide back and not allow new blad to install....(Answered by cmantx2003)

View Entire Answer \| Report Abuse \| See it in Y!

Bostich-Stanley nail gun will not drive nails in. This is the coil nailer I use for sheathing.? I have noticed that the plunger is visible when it will not cycle to fire the next nail. I have taken the trigger mechanism apart and put in new o rings, it worked for awhile and then quit again. When you hold the trigger back and bump the safty on the front end it will not drive a nail. I have taken the back of it apart where the big diapham is and everything seems okay back there. The feed is okay on it. When the trigger is pulled and you bump the front end ... (Asked by Thomas S)
View Entire Question \| Report Abuse \| Similar Questions \| See it in Y!
A.
is the presure high enough on comp. do you use air tool oil?...(Answered by paratile)

View Entire Answer \| Report Abuse \| See it in Y!

where can i buy stanley steemer products? can i get them at walmart? ... (Asked by kristi_b00)
View Entire Question \| Report Abuse \| Similar Questions \| See it in Y!
A.
Try this site: http://www.stanleymuseum.org/book.html Lots of good info on them as well !...(Answered by Ross G)

View Entire Answer \| Report Abuse \| See it in Y!

I have stanley garage door approx. 13 years old.I need plastic panels in front of glass? decorative trim pieces there plastic and they broke ... (Asked by tm)
View Entire Question \| Report Abuse \| Similar Questions \| See it in Y!
A.
Any hardware store can cut new pieces for you. You can get glass or acrylic....(Answered by n0witrytobeamused)

View Entire Answer \| Report Abuse \| See it in Y!

Note: We are not affiliated with Yahoo! Answers in any way. All the content is retrieved from Yahoo! Answers. We are not responsible for the content. For more information, please see the term of service. The above content was retrieved on July 09 2008 02:22:28.from Yahoo! Answers (Category Home > Home & Garden > Maintenance & Repairs). We are neither affiliated with the authors of this page nor responsible for its content. The data may have changed since that time. Click here to search real time questions/answers from Yahoo! Answers.